# Heat treating 1084

> 1084 knife heat treatment with Celsius and Fahrenheit setpoints, hold times, quench and temper details, equipment assumptions and workshop checks.

Source: https://knifetemplates.com/heat-treating/1084

[Learn](https://knifetemplates.com/guides) / [Heat treating](https://knifetemplates.com/heat-treating)

If I were setting up for an early carbon-steel build, 1084 would be on the shortlist. The attraction is a manageable process, provided you still control the heat and use a suitable quench.

[Knife Templates](https://knifetemplates.com/makers/knife-templates) · 4 min read

## Where I would start

A useful candidate for general-purpose carbon-steel knives. Decide on the geometry and care routine before worrying about squeezing another hardness point out of it. It will rust if left wet.

Known annealed 1084 bar used for stock removal. This example follows the NJSB hardening and tempering window. It does not include a forged-blade normalising sequence.

## Get the equipment ready

A controlled furnace, suitable anti-scale protection, Parks 50 quench oil used within its operating instructions, and a checked tempering oven.

Measure the furnace and tempering oven independently where possible. A controller display is a setpoint, not proof that the whole blade has reached it. Timing a hold starts after equalisation, not as soon as the door closes.

## A process to work from

Use this as a complete route to establish on a coupon from your stock. Temperatures in Celsius are rounded conversions of the Fahrenheit setpoints. A different supplier, section or starting condition can need a different process.

*1084: worked heat-treatment route*

| Stage | What to do |
| --- | --- |
| Prepare | Finish the profile, holes and burr removal while soft. Leave measurable cleanup stock on the faces and edge. |
| Austenitise | Example: 802°C / 1475°F. Hold 10 minutes after the blade equalises. The supplier allows 5–15 minutes depending on section and equipment. |
| Quench | Transfer promptly into Parks 50. Follow the oil maker’s temperature, tank and agitation instructions. |
| Temper | When near room temperature, temper at 204°C / 400°F for 2 hours. Cool to room temperature, then repeat for another 2 hours. |
| Check | Clean the test area and measure hardness on a suitable flat coupon. Check the tempered blade for cracks and straightness. |

### Before the blade gets hot

Have the tempering setup ready. Oil quenching needs a stable non-combustible tank, sufficient depth and volume, a fitted metal lid, ventilation and suitable fire protection. Keep water away from quench oil. Never use waste motor oil.

### How far to trust this route

This 1084 route follows New Jersey Steel Baron's published sheet for annealed bar, and its numbers match that sheet. Independent testing advises caution with that supplier's datasheets: many of them seem to carry the same recommendations regardless of the steel, and the advice is to avoid them. Reading the 1084, 1095 and O1 sheets (that supplier's O1 sheet is among them) side by side, their tempering hardness tables are identical wherever they overlap, and all four carbon steel sheets carry the same three-step normalising block, which fits what the independent testing describes. I looked for the steel producers' own heat treatment figures for 1084 and 1095 and found none. The only non-retail table I found, a furnace maker's reference (SECO/WARWICK's Heat Treating Data Book), gives a hardening range of 1575 to 1625°F for both, about 100°F hotter than this route, and no tempering temperature. I have kept the route because it is a complete, self-consistent starting point for a coupon. Cross-check it against the steel producer's own datasheet before you rely on any figure.

## The detail to pay attention to

1084 is sometimes described as needing no soak. That can refer to a different starting structure or heating method. This is a furnace route for annealed stock; do not substitute an unmeasured colour judgement for its equalisation and hold.

Keep one offcut from the same bar with the same surface protection. It is easier to establish your furnace timing and quench response on that coupon than on the tip of a nearly finished knife. Once it is repeatable, keep the process fixed while you learn the grinding.

## Check the result before fitting the handle

Clean scale and decarburisation from the test surface before interpreting a hardness reading. Use a flat, supported area and a calibrated method appropriate to the sample thickness. A file skating across a blade is a rough check, not an HRC measurement.

Inspect the tempered blade in good light for cracks, edge waves and distortion. If a blade is cracked, retire it. If hardness is unexpectedly low, check the whole record before increasing temperature or repeating a quench.

## Keep a record

Keep the stock supplier and batch, blade and edge thickness, furnace program, actual hold, oil or plate details, cold-treatment branch and temper cycles beside the editable design. Add measured hardness and where it was measured.

After grinding and sharpening, evaluate the finished knife in its intended cutting work. Keep notes on edge stability, sharpening and geometry. Change one main variable so you can tell what helped as you learn.

## Where this comes from

- [1084 Heat Treat, July 2020](https://newjerseysteelbaron.com/1084-heat-treat-7-20/), New Jersey Steel Baron. Supplier schedule for controlled equipment. Fahrenheit is authoritative where the PDF prints an inconsistent Celsius conversion. Example setpoints below sit inside its ranges; no hardness is guaranteed.
- [Heat Treating Data Book, tenth edition, Table 2](https://www.secowarwick.com/wp-content/uploads/2017/03/HeatTreatingDataEBook.2011.pdf), SECO/WARWICK. A furnace maker’s reference table of heat treating grades of carbon steels, compiled from sources it believes reliable. It is not a steel producer. It gives a hardening range for 1084 and 1095 but no tempering temperature.

[Next up Heat treating 1095 1095: the equipment, hardening hold, quench, temper and details that are easy to miss.](https://knifetemplates.com/heat-treating/1095)

## Keep reading

- [Knife steel: 1084](https://knifetemplates.com/steel/1084)
- [Austenitising a knife: temperature and soak](https://knifetemplates.com/heat-treating/austenitising)
- [Quenching knives: oils, plates and speed](https://knifetemplates.com/heat-treating/quenching)
- [Tempering knife steel: temperature and cycles](https://knifetemplates.com/heat-treating/tempering)
- [How to heat treat a knife](https://knifetemplates.com/heat-treating)
- [All heat treating pages](https://knifetemplates.com/heat-treating)

## Put it into practice

[Choose a template](https://knifetemplates.com/templates) [Read the print guide](https://knifetemplates.com/guides/print-at-actual-size) [Arrange blanks on stock](https://knifetemplates.com/nest)
