# Heat treating 52100

> 52100 knife heat treatment with Celsius and Fahrenheit setpoints, hold times, quench and temper details, equipment assumptions and workshop checks.

Source: https://knifetemplates.com/heat-treating/52100

[Learn](https://knifetemplates.com/guides) / [Heat treating](https://knifetemplates.com/heat-treating)

52100 rewards a bit of attention to what happened before the final hardening heat. I would keep the whole process together here, including the anneal, rather than copy the last two temperatures from somebody’s notes.

[Knife Templates](https://knifetemplates.com/makers/knife-templates) · 4 min read

## Where I would start

A non-stainless bearing steel used for fine cutting blades. Known bar makes the starting point much clearer than an unidentified bearing race. Chromium in its composition does not make it stainless.

The researched fine-carbide DET route below includes its own prior processing. This is an advanced controlled-furnace example, not a claim that every commercially annealed bar needs these extra steps.

## Get the equipment ready

A programmable furnace that can control the annealing cool, surface protection, Parks 50 oil and a calibrated tempering oven.

Measure the furnace and tempering oven independently where possible. A controller display is a setpoint, not proof that the whole blade has reached it. Timing a hold starts after equalisation, not as soon as the door closes.

## A process to work from

Use this as a complete route to establish on a coupon from your stock. Temperatures in Celsius are rounded conversions of the Fahrenheit setpoints. A different supplier, section or starting condition can need a different process.

*52100: worked heat-treatment route*

| Stage | What to do |
| --- | --- |
| Normalise | 927°C / 1700°F for 20 minutes, then air cool. |
| Refine | 793°C / 1460°F for 30 minutes, then air cool. |
| DET anneal | 793°C / 1460°F for 30 minutes. Furnace cool at about 372°C per hour / 670°F per hour to 682°C / 1260°F, then air cool. |
| Austenitise | Example: 816°C / 1500°F for 15 minutes after equalisation. The researched window is 1500–1525°F. |
| Quench | Fast oil; Parks 50 was used. This example follows the non-cryo branch. |
| Temper | 204°C / 400°F for 1 hour, cool to room temperature, then repeat for 1 hour, matching the experiments. |

### Before the blade gets hot

Have the tempering setup ready. Oil quenching needs a stable non-combustible tank, sufficient depth and volume, a fitted metal lid, ventilation and suitable fire protection. Keep water away from quench oil. Never use waste motor oil.

## The detail to pay attention to

DET means divorced eutectoid transformation: an annealing route, not an extra quench. Commercial spheroidised bar may not respond identically. A successful process on that stock does not need to be replaced just to match this worked example.

Record the cooling program as well as the hardening hold. Check your furnace can actually follow it before loading a blade. I would run a coupon through the whole sequence first and compare the measured result with an existing process, rather than add cycles and assume the knife improved.

## Check the result before fitting the handle

Clean scale and decarburisation from the test surface before interpreting a hardness reading. Use a flat, supported area and a calibrated method appropriate to the sample thickness. A file skating across a blade is a rough check, not an HRC measurement.

Inspect the tempered blade in good light for cracks, edge waves and distortion. If a blade is cracked, retire it. If hardness is unexpectedly low, check the whole record before increasing temperature or repeating a quench.

## Keep a record

Keep the stock supplier and batch, blade and edge thickness, furnace program, actual hold, oil or plate details, cold-treatment branch and temper cycles beside the editable design. Add measured hardness and where it was measured.

After grinding and sharpening, evaluate the finished knife in its intended cutting work. Keep notes on edge stability, sharpening and geometry. Change one main variable so you can tell what helped as you learn.

## Where this comes from

- [How to Heat Treat 52100](https://knifesteelnerds.com/2019/05/13/how-to-heat-treat-52100/), Knife Steel Nerds. Original experiments by metallurgist Larrin Thomas. Starting microstructure, hold and quench stay together. Do not transfer experimental property values to a different process.

[Next up Heat treating O1 O1: the equipment, hardening hold, quench, temper and details that are easy to miss.](https://knifetemplates.com/heat-treating/o1)

## Keep reading

- [Knife steel: 52100](https://knifetemplates.com/steel/52100)
- [Annealing knife steel](https://knifetemplates.com/heat-treating/annealing)
- [Normalising and thermal cycling](https://knifetemplates.com/heat-treating/normalising)
- [Austenitising a knife: temperature and soak](https://knifetemplates.com/heat-treating/austenitising)
- [Quenching knives: oils, plates and speed](https://knifetemplates.com/heat-treating/quenching)
- [Tempering knife steel: temperature and cycles](https://knifetemplates.com/heat-treating/tempering)
- [How to heat treat a knife](https://knifetemplates.com/heat-treating)
- [All heat treating pages](https://knifetemplates.com/heat-treating)

## Put it into practice

[Choose a template](https://knifetemplates.com/templates) [Read the print guide](https://knifetemplates.com/guides/print-at-actual-size) [Arrange blanks on stock](https://knifetemplates.com/nest)
