# Heat treating AEB-L

> AEB-L knife heat treatment with Celsius and Fahrenheit setpoints, hold times, quench and temper details, equipment assumptions and workshop checks.

Source: https://knifetemplates.com/heat-treating/aeb-l

[Learn](https://knifetemplates.com/guides) / [Heat treating](https://knifetemplates.com/heat-treating)

AEB-L is worth a look for a stainless kitchen knife, especially when you want a fine edge. The workshop requirement steps up from simple carbon steel: controlled high heat, protection from the atmosphere and a planned cold treatment.

[Knife Templates](https://knifetemplates.com/makers/knife-templates) · 5 min read

## Where I would start

A fine-carbide stainless steel used in cutting applications. Stainless still needs cleaning and drying; a completed heat treatment and suitable finish are part of getting the corrosion performance you expect.

Annealed AEB-L, controlled furnace and the NJSB plate-quench plus cold-treatment route. A lower-temperature route without cold treatment is a different process and has different retained-austenite behaviour.

## Get the equipment ready

A furnace capable of stable stainless hardening temperatures, correctly rated stainless foil or another suitable protective system, aluminium quench plates, compressed air and a properly managed sub-zero setup.

Measure the furnace and tempering oven independently where possible. A controller display is a setpoint, not proof that the whole blade has reached it. Timing a hold starts after equalisation, not as soon as the door closes.

## A process to work from

Use this as a complete route to establish on a coupon from your stock. Temperatures in Celsius are rounded conversions of the Fahrenheit setpoints. A different supplier, section or starting condition can need a different process.

*AEB-L: worked heat-treatment route*

| Stage | What to do |
| --- | --- |
| Protect and preheat | Use a clean, correctly sealed, temperature-rated foil packet. Preheat at 816°C / 1500°F for 15 minutes. |
| Austenitise | 1066°C / 1950°F for 15 minutes after equalisation. |
| Quench | Quench between aluminium plates with compressed air to 50°C / 125°F or below. Keep plate contact effective across the blade. |
| Cold treatment | After cooling to room temperature, use the specified sub-zero route: approximately −74°C / −100°F for 30–60 minutes. Liquid nitrogen is an alternative in the supplier’s process; it is not the same temperature as a dry-ice bath. |
| Temper | Return to room temperature, then 177°C / 350°F for 2 hours. Cool to room temperature and repeat for 2 hours. Cold treatment must be followed by tempering. |

### Before the blade gets hot

Have the tempering setup ready. Oil quenching needs a stable non-combustible tank, sufficient depth and volume, a fitted metal lid, ventilation and suitable fire protection. Keep water away from quench oil. Never use waste motor oil.

### How far to trust this route

This AEB-L route follows New Jersey Steel Baron's published sheet for annealed bar, and its numbers match that sheet. Independent testing advises caution with that supplier's datasheets: many of them seem to carry the same recommendations regardless of the steel, and the advice is to avoid them. This sheet is specific to AEB-L (preheat, plate quench, cold treatment), but steel sold as AEB-L can also be Buderus X65Cr13, which needed about 50°F higher austenitizing temperatures for the same hardness in cold treatment testing, so ask your supplier which one you have. I have kept the route because it is a complete, self-consistent starting point for a coupon. Cross-check it against the steel producer's own datasheet before you rely on any figure.

## The detail to pay attention to

A household freezer does not reproduce a −74°C bath. Do not raise the hardening temperature to compensate for missing cold-treatment equipment. Select and validate a complete no-cold route if that is the process you can actually run. The producer’s own sheet, an old undated scan for the strip steel, is a different route: harden at 1050°C (1920°F) and cool to room temperature, or at 1080°C (1975°F) with a subzero treatment to −60°C (−76°F), in oil and not water, with the hold read from a graph and the heating-up time added. It says a temper of at least 150°C (300°F) is needed for a minimum of toughness, and that tempering above about 400°C (750°F) loses the corrosion resistance. Keep the two apart.

Thin kitchen blades make quench contact worth planning. The packet should not have a folded seam between a blade face and a plate. Rehearse handling with a cold packet. Cryogenic liquids need a suitable vessel, ventilation, face and hand protection, and training; never use a sealed container or improvise a flammable solvent bath beside a hot furnace.

## Check the result before fitting the handle

Clean scale and decarburisation from the test surface before interpreting a hardness reading. Use a flat, supported area and a calibrated method appropriate to the sample thickness. A file skating across a blade is a rough check, not an HRC measurement.

Inspect the tempered blade in good light for cracks, edge waves and distortion. If a blade is cracked, retire it. If hardness is unexpectedly low, check the whole record before increasing temperature or repeating a quench.

## Keep a record

Keep the stock supplier and batch, blade and edge thickness, furnace program, actual hold, oil or plate details, cold-treatment branch and temper cycles beside the editable design. Add measured hardness and where it was measured.

After grinding and sharpening, evaluate the finished knife in its intended cutting work. Keep notes on edge stability, sharpening and geometry. Change one main variable so you can tell what helped as you learn.

## Where this comes from

- [AEB-L Heat Treat, July 2020](https://cdn.newjerseysteelbaron.com/wp-content/uploads/2020/07/AEB-L-Heat-Treat-7-20.pdf), New Jersey Steel Baron. Supplier schedule for controlled equipment. Fahrenheit is authoritative where the PDF prints an inconsistent Celsius conversion. Example setpoints below sit inside its ranges; no hardness is guaranteed.
- [UHB Stainless AEB-L data sheet (undated scan)](https://knifesteelnerds.com/wp-content/uploads/2019/03/AEB-L-datasheet.pdf), Uddeholm. The producer’s own sheet for the strip steel, as a scan hosted by Knife Steel Nerds. It is undated, I found no current producer sheet, and it gives hold times only as a graph. Producer data, and a different route from the supplier’s.

[Next up Heat treating CPM MagnaCut CPM MagnaCut: the equipment, hardening hold, quench, temper and details that are easy to miss.](https://knifetemplates.com/heat-treating/cpm-magnacut)

## Keep reading

- [Knife steel: AEB-L](https://knifetemplates.com/steel/aeb-l)
- [Foil or coatings: protecting knife steel](https://knifetemplates.com/heat-treating/protecting-the-steel)
- [Cold treatment and cryo for knives](https://knifetemplates.com/heat-treating/cold-treatment)
- [Austenitising a knife: temperature and soak](https://knifetemplates.com/heat-treating/austenitising)
- [Quenching knives: oils, plates and speed](https://knifetemplates.com/heat-treating/quenching)
- [Tempering knife steel: temperature and cycles](https://knifetemplates.com/heat-treating/tempering)
- [How to heat treat a knife](https://knifetemplates.com/heat-treating)
- [All heat treating pages](https://knifetemplates.com/heat-treating)

## Put it into practice

[Choose a template](https://knifetemplates.com/templates) [Read the print guide](https://knifetemplates.com/guides/print-at-actual-size) [Arrange blanks on stock](https://knifetemplates.com/nest)
