# Heat treating CPM-154

> CPM-154 knife heat treatment with Celsius and Fahrenheit setpoints, hold times, quench and temper details, equipment assumptions and workshop checks.

Source: https://knifetemplates.com/heat-treating/cpm-154

[Learn](https://knifetemplates.com/guides) / [Heat treating](https://knifetemplates.com/heat-treating)

CPM-154 is a powder metallurgy stainless steel that was tested at length, including a toughness result that could not be explained. The route is a hot, cold-treated one, and makers are told to prefer a different datasheet from the producer's.

[Knife Templates](https://knifetemplates.com/makers/knife-templates) · 4 min read

## Where I would start

A stainless steel known for its ease in finishing, combined with good all-around properties including good potential hardness, edge retention and toughness. Crucible's sheet lists "cutlery, bearings, and corrosion resistant tooling" as its typical applications.

The recommended route for CPM-154. The coupons were wrapped in stainless foil. The producer's data sheet describes a different route, covered in the catch below.

## Get the equipment ready

A furnace holding about 1950°F (1066°C), stainless foil for the hold, aluminium quench plates, liquid nitrogen and a checked tempering oven. The maximum-hardness variant runs at 2025°F (1107°C).

Measure the furnace and tempering oven independently where possible. A controller display is a setpoint, not proof that the whole blade has reached it. Timing a hold starts after equalisation, not as soon as the door closes.

## A process to work from

Use this as a complete route to establish on a coupon from your stock. Temperatures in Celsius are rounded conversions of the Fahrenheit setpoints. A different supplier, section or starting condition can need a different process.

*CPM-154: worked heat-treatment route*

| Stage | What to do |
| --- | --- |
| Prepare | Finish the profile, holes and burr removal while soft. Leave measurable cleanup stock on the faces and edge. |
| Austenitise | Wrapped in stainless foil, 1950°F (1066°C) for 30 minutes. The optimum found for CPM-154 was 1950°F for 30 minutes with a plate quench and cryo. |
| Quench | Plate quench between aluminium plates. |
| Cold step | Liquid nitrogen. The source article gives no time. Dry ice would likely work similarly, though that was not tested, and these heat treatments should not be assumed to work without cryo. |
| Temper | Twice for two hours each time, between 300 and 450°F (149 to 232°C) depending on the hardness you want. Tempering lower than 300°F is not normally recommended. For the most hardness, a maximum hardness heat treatment (about 64 Rc) with decent toughness was 2025°F for 20 minutes with a plate quench and cryo followed by a 300°F temper. |

### Before the blade gets hot

Have the tempering setup ready. Oil quenching needs a stable non-combustible tank, sufficient depth and volume, a fitted metal lid, ventilation and suitable fire protection. Keep water away from quench oil. Never use waste motor oil.

## The detail to pay attention to

The testing recommends a different datasheet from the producer's: use the Latrobe datasheet rather than Crucible's for heat treating 154CM and CPM-154. The producer's sheet, as a distributor publishes it, hardens at 1900 to 2000°F for 30 to 60 minutes (twice the tested hold), quenches in oil, gas or salt, freezes in dry ice at -100°F, tempers twice at 400 to 1200°F and says to avoid 800 to 1100°F. Keep the two routes apart. Without a cold step, the peak austenitising temperature is probably lower: Latrobe and Hitachi data suggest 1900 to 1925°F, which was not tested.

Run a coupon first, and treat an unusually good toughness number with suspicion, as the testing itself did. An earlier measurement just looked too high: every other steel with a similar carbide content was maxing out around 10 ft-lbs, and there was no clear reason why CPM-154 would manage such high toughness.

## Check the result before fitting the handle

Clean scale and decarburisation from the test surface before interpreting a hardness reading. Use a flat, supported area and a calibrated method appropriate to the sample thickness. A file skating across a blade is a rough check, not an HRC measurement.

Inspect the tempered blade in good light for cracks, edge waves and distortion. If a blade is cracked, retire it. If hardness is unexpectedly low, check the whole record before increasing temperature or repeating a quench.

## Keep a record

Keep the stock supplier and batch, blade and edge thickness, furnace program, actual hold, oil or plate details, cold-treatment branch and temper cycles beside the editable design. Add measured hardness and where it was measured.

After grinding and sharpening, evaluate the finished knife in its intended cutting work. Keep notes on edge stability, sharpening and geometry. Change one main variable so you can tell what helped as you learn.

## Where this comes from

- [How to Heat Treat CPM-154: Toughness Experiments](https://knifesteelnerds.com/2020/03/16/how-to-heat-treat-cpm-154-toughness-experiments/), Knife Steel Nerds. Larrin Thomas’s hardness and toughness tests of CPM-154, with datasheet comparisons. It includes an earlier toughness result he could not explain. The charts are images, so this site quotes only the text.
- [CPM 154 data sheet](https://nsm-ny.com/content/uploads/2021/07/CPM154ds.pdf), Niagara Specialty Metals. The CPM 154 data sheet as published by a distributor of Crucible’s CPM steels; Crucible’s own copy was not reachable, and the copy is undated. Producer data, a different route from Larrin Thomas’s, and he advises preferring another datasheet.

## Keep reading

- [Knife steel: CPM-154](https://knifetemplates.com/steel/cpm-154)
- [Foil or coatings: protecting knife steel](https://knifetemplates.com/heat-treating/protecting-the-steel)
- [Cold treatment and cryo for knives](https://knifetemplates.com/heat-treating/cold-treatment)
- [Austenitising a knife: temperature and soak](https://knifetemplates.com/heat-treating/austenitising)
- [Quenching knives: oils, plates and speed](https://knifetemplates.com/heat-treating/quenching)
- [Tempering knife steel: temperature and cycles](https://knifetemplates.com/heat-treating/tempering)
- [How to heat treat a knife](https://knifetemplates.com/heat-treating)
- [All heat treating pages](https://knifetemplates.com/heat-treating)

## Put it into practice

[Choose a template](https://knifetemplates.com/templates) [Read the print guide](https://knifetemplates.com/guides/print-at-actual-size) [Arrange blanks on stock](https://knifetemplates.com/nest)
