# Heat treating knives in an electric furnace

> What an electric furnace gives you over a forge, the evenness and tempering-oven details that catch people out, and what the stainless steels add.

Source: https://knifetemplates.com/heat-treating/in-a-furnace

[Learn](https://knifetemplates.com/guides) / [Heat treating](https://knifetemplates.com/heat-treating)

A controlled furnace takes the guesswork out of the temperature, which is most of the problem. It does not take the care out of the rest.

[Knife Templates](https://knifetemplates.com/makers/knife-templates) · 2 min read

## Why a furnace

A furnace with a controller is a preferred way of heat treating and is said to give consistent results every time. That is a claim, not a measurement, but the logic is plain. A controller holds a setpoint, so a blade that reached a temperature last time reaches it again.

Controller and blade are not the same thing. A display is a setpoint, not proof that the whole blade has reached it. The routes here start the soak timer after the steel has equalised, not when the door closes.

## Evenness

The temperature is usually somewhat different at the ends of the furnace, especially right next to the door. Keep blades away from the door and the walls. One furnace was measured in detail, and those numbers are that furnace's, so measure yours rather than assume.

## Tempering

A regular furnace "can also be used for tempering but they aren't 'tuned' and calibrated for low temperature." A conventional oven works, "though the temperature will be more variable." Either way, check the temperature against a good thermometer.

## What the stainless steels add

AEB-L and MagnaCut need a furnace that holds high, stable temperatures: the routes here run to 1066°C (1950°F) and 1121°C (2050°F). They also need foil or an atmosphere rated for that heat, quench plates, and for AEB-L a managed cold treatment. Plan the whole bench before you buy the bar.

## Where this comes from

- [Introduction to Knife Steel Heat Treating from a Metallurgist](https://knifesteelnerds.com/2024/09/17/introduction-to-knife-steel-heat-treating-from-a-metallurgist/), Knife Steel Nerds. The stages, equipment, datasheets and what to do when datasheets disagree. Larrin Thomas’s own recommendations; it gives no schedule for a particular steel.
- [How Even is an EvenHeat? How to Operate Furnaces Effectively](https://knifesteelnerds.com/2021/04/13/how-even-is-an-evenheat-how-to-operate-furnaces-effectively/), Knife Steel Nerds. One furnace, one set-up, measured. The numbers are that furnace’s; other furnaces will differ.
- [How to Use a Steel Datasheet to Develop a Heat Treatment](https://knifesteelnerds.com/2021/03/01/how-to-use-a-steel-datasheet-to-develop-a-heat-treatment/), Knife Steel Nerds. Reading a producer datasheet: soak, temper and temperature choices. Larrin Thomas’s recommendations, not a standard.

[Next up Heat treating knives in a salt pot What salt gives you, why it suits a narrow range of steels, and the water rule.](https://knifetemplates.com/heat-treating/in-a-salt-pot)

## Keep reading

- [Austenitising a knife: temperature and soak](https://knifetemplates.com/heat-treating/austenitising)
- [Tempering knife steel: temperature and cycles](https://knifetemplates.com/heat-treating/tempering)
- [Foil or coatings: protecting knife steel](https://knifetemplates.com/heat-treating/protecting-the-steel)
- [Knife steel: CPM MagnaCut](https://knifetemplates.com/steel/cpm-magnacut)
- [All heat treating pages](https://knifetemplates.com/heat-treating)

## Put it into practice

[Choose a template](https://knifetemplates.com/templates) [Read the print guide](https://knifetemplates.com/guides/print-at-actual-size) [Arrange blanks on stock](https://knifetemplates.com/nest)
