# Normalising and thermal cycling

> What normalising does, why forged knives need it, why stainless steel is annealed instead, and why I would skip grain refinement cycles.

Source: https://knifetemplates.com/heat-treating/normalising

[Learn](https://knifetemplates.com/guides) / [Heat treating](https://knifetemplates.com/heat-treating)

Normalising is the step that makes forged steel ready to be annealed and hardened. Most of what gets called thermal cycling is a vague name for it.

[Knife Templates](https://knifetemplates.com/makers/knife-templates) · 2 min read

## What normalising does

Normalising heats the steel above its usual austenitising temperature and lets it cool in air. It "gives the steel a uniform microstructure and grain size." The datasheet rule of thumb is to normalise "by heating to the recommended temperature for 10-15 minutes and air cool."

The point is a clean start: forging takes the steel out of its annealed condition, and normalising gives it a consistent one before the anneal.

## Thermal cycling is a vague word

Be wary of the term: 'thermal cycling' is very non-specific, it just means heating and cooling steel. When someone says they thermal cycle, ask what temperatures, how many times, and what the cooling was.

## When you cannot normalise

"Stainless steels and high alloy tool steels cannot be normalized." If you forge those, go straight to the anneal. The stainless anneal has its own page.

## The grain refinement cycles

Many knifemakers add several lower-temperature cycles after normalising, aiming for finer grain. It is an optional step, usually labelled 'grain refinement', and one that is generally best skipped. The reasoning: changes to the carbide structure and heat treatment response are much more significant than any changes to grain size.

That is one metallurgist's view, backed by tests, and plenty of bladesmiths do it anyway. I mention it so you know it is a choice, not a rule.

## If you heat treat in a forge

The forge method starts from a normalised, pearlitic structure: heat to nonmagnet and no hotter. The forge method has its own page.

## Where this comes from

- [Introduction to Knife Steel Heat Treating from a Metallurgist](https://knifesteelnerds.com/2024/09/17/introduction-to-knife-steel-heat-treating-from-a-metallurgist/), Knife Steel Nerds. The stages, equipment, datasheets and what to do when datasheets disagree. Larrin Thomas’s own recommendations; it gives no schedule for a particular steel.
- [How to Thermal Cycle Knife Steel](https://knifesteelnerds.com/2021/08/28/how-to-thermal-cycle-knife-steel/), Knife Steel Nerds. Normalising, annealing and grain refinement for knife steels, with datasheet-style rules of thumb. It does not give a blanket rule for when a forged knife needs which step.
- [How to Heat Treat Knife Steel in a Forge](https://knifesteelnerds.com/2021/09/23/how-to-heat-treat-knife-steel-in-a-forge/), Knife Steel Nerds. A method for reducing forge error, tested on seven low alloy steels. The author still recommends a furnace or a professional for most people.

[Next up Austenitising a knife: temperature and soak The hardening heat: temperature, soak, preheat, datasheets and the magnet.](https://knifetemplates.com/heat-treating/austenitising)

## Keep reading

- [Annealing knife steel](https://knifetemplates.com/heat-treating/annealing)
- [Heat treating knives in a forge](https://knifetemplates.com/heat-treating/in-a-forge)
- [Knife steel: 5160](https://knifetemplates.com/steel/5160)
- [All heat treating pages](https://knifetemplates.com/heat-treating)

## Put it into practice

[Choose a template](https://knifetemplates.com/templates) [Read the print guide](https://knifetemplates.com/guides/print-at-actual-size) [Arrange blanks on stock](https://knifetemplates.com/nest)
