# Knife steel: 1095

> What 1095 is, why its toughness tests low and 52100 is recommended instead, and what it asks of the quench.

Source: https://knifetemplates.com/steel/1095

[Learn](https://knifetemplates.com/guides) / [Steel](https://knifetemplates.com/steel)

1095 is familiar, but I would not pick it just because the name sounds simple. The quick transfer and fast quench deserve as much attention as the temperature.

[Knife Templates](https://knifetemplates.com/makers/knife-templates) · 2 min read

## What it is

1095 is a simple carbon steel with 0.95% carbon and small amounts of Mn and Si. Like 1084 it is not stainless, so it rusts if left wet.

## What the testing found

The finding to know: O1 and 1095 both showed relatively low toughness in earlier testing, likely because of plate martensite. The recommendation follows from it: 52100 over 1095 or O1 on toughness testing.

Plenty of makers like 1095 and make good knives from it, and a well-heat-treated blade is a good knife. The point is that the margin for error is smaller than the name suggests. In the forge testing, 1095 is on the list for fine cutting knives like kitchen knives, with 52100 the pick of the three.

## What it asks of the maker

It needs a fast quench, which is why the route here names Parks 50. Oil testing makes the general point: if you buy only one oil, make it a fast oil like Parks 50 so that you can quench the low hardenability steels.

## Where this comes from

- [Bainite Heat Treatments of 52100, O1, and 1095: How Much Toughness?](https://knifesteelnerds.com/2021/06/07/bainite-heat-treatments-of-52100-o1-and-1095-how-much-toughness/), Knife Steel Nerds. Austempering experiments and what they say about plate martensite in 1095 and O1. A different route from quench and temper.
- [How to Pick the Best Steel for Every Knife](https://knifesteelnerds.com/2019/05/20/how-to-pick-the-best-steel-for-every-knife/), Knife Steel Nerds. Larrin Thomas’s method for choosing a steel, with his own recommendations. Opinion informed by his testing; the charts are images.
- [How to Heat Treat Knife Steel in a Forge](https://knifesteelnerds.com/2021/09/23/how-to-heat-treat-knife-steel-in-a-forge/), Knife Steel Nerds. A method for reducing forge error, tested on seven low alloy steels. The author still recommends a furnace or a professional for most people.
- [Which Quenching Oil is Best for Knives?](https://knifesteelnerds.com/2021/07/19/which-quenching-oil-is-best-for-knives/), Knife Steel Nerds. Hardness after quenching in several oils, on low alloy steels. Toughness was not tested in this article, and only one canola product was used.
- [1095 Heat Treat, July 2020](https://cdn.newjerseysteelbaron.com/wp-content/uploads/2020/07/1095-Heat-Treat-7-20.pdf), New Jersey Steel Baron. Supplier schedule for controlled equipment. Fahrenheit is authoritative where the PDF prints an inconsistent Celsius conversion. Example setpoints below sit inside its ranges; no hardness is guaranteed.

[Next up Knife steel: 80CrV2 A low alloy steel with good toughness and hardenability, but low wear resistance.](https://knifetemplates.com/steel/80crv2)

## Keep reading

- [1084 or 1095?](https://knifetemplates.com/steel/1084-vs-1095)
- [Knife steel: 52100](https://knifetemplates.com/steel/52100)
- [Knife steel: O1](https://knifetemplates.com/steel/o1)
- [Knife steel: 1084](https://knifetemplates.com/steel/1084)
- [Choosing steel for a knife](https://knifetemplates.com/steel)
- [All steel pages](https://knifetemplates.com/steel)

## Put it into practice

[Choose a template](https://knifetemplates.com/templates) [Read the print guide](https://knifetemplates.com/guides/print-at-actual-size) [Arrange blanks on stock](https://knifetemplates.com/nest)
