# Knife steel: 5160

> What 5160 is, why its toughness ranks second only to 8670, and the narrow tempering window the tests found.

Source: https://knifetemplates.com/steel/5160

[Learn](https://knifetemplates.com/guides) / [Steel](https://knifetemplates.com/steel)

5160 often comes up when makers talk about tough working blades. I would start with identified bar and a repeatable schedule rather than an unknown spring with years of service behind it.

[Knife Templates](https://knifetemplates.com/makers/knife-templates) · 2 min read

## What it is

5160 is a low alloy steel known for its excellent toughness. It is used by many forging bladesmiths for its good properties, and it is common in the form of leaf springs. It is not stainless.

## What the testing found

In Charpy tests on 2.5 x 10 x 55 mm specimens without any notch, 5160 was better than any other steel apart from 8670. The best result came from a process of its own: austenitizing at 1500-1525°F and tempering at 375-400°F gave the best combination of properties, with a quench in Parks 50 oil followed by 15 minutes in liquid nitrogen.

The window is narrow: tempering above 400 or below 375°F is not recommended. It is also a choice for big work, since 8670 and 5160 are good choices for large knives that need very high toughness.

## Where to be careful

That optimum belongs to a process that included liquid nitrogen. The worked route on this site is a different one, from a supplier sheet, and the two should not be mixed: keep the hardening temperature, quench, cold step and temper together from one source. The route page says more.

If you cannot identify a recycled spring, treat it as experimental stock rather than calling the knife 5160.

## Where this comes from

- [How to Heat Treat 5160: Optimizing Toughness](https://knifesteelnerds.com/2019/04/01/how-to-heat-treat-5160/), Knife Steel Nerds. Charpy tests of 5160 across austenitising and tempering temperatures, including a liquid nitrogen step. Its optimum belongs to that process.
- [Knife Steels Rated by a Metallurgist: Toughness, Edge Retention, and Corrosion Resistance](https://knifesteelnerds.com/2021/10/19/knife-steels-rated-by-a-metallurgist-toughness-edge-retention-and-corrosion-resistance/), Knife Steel Nerds. One metallurgist’s ratings, which he says he may change. The rating tables are images, so this site quotes only the text.
- [How to Heat Treat Knife Steel in a Forge](https://knifesteelnerds.com/2021/09/23/how-to-heat-treat-knife-steel-in-a-forge/), Knife Steel Nerds. A method for reducing forge error, tested on seven low alloy steels. The author still recommends a furnace or a professional for most people.
- [5160 Heat Treat, July 2020](https://cdn.newjerseysteelbaron.com/wp-content/uploads/2020/07/5160-Heat-Treat-7-20.pdf), New Jersey Steel Baron. Supplier schedule for controlled equipment. Fahrenheit is authoritative where the PDF prints an inconsistent Celsius conversion. Example setpoints below sit inside its ranges; no hardness is guaranteed.

[Next up Knife steel: 52100 A non-stainless bearing steel with good toughness and a fine edge.](https://knifetemplates.com/steel/52100)

## Keep reading

- [5160 or 80CrV2?](https://knifetemplates.com/steel/5160-vs-80crv2)
- [Knife steel: 80CrV2](https://knifetemplates.com/steel/80crv2)
- [Identifying stock steel](https://knifetemplates.com/steel/identifying-stock-steel)
- [Choosing steel for a knife](https://knifetemplates.com/steel)
- [All steel pages](https://knifetemplates.com/steel)

## Put it into practice

[Choose a template](https://knifetemplates.com/templates) [Read the print guide](https://knifetemplates.com/guides/print-at-actual-size) [Arrange blanks on stock](https://knifetemplates.com/nest)
