# Knife steel: 80CrV2

> What 80CrV2 is, its toughness and hardenability from the tests, why its edge retention is low, and the tempering limit.

Source: https://knifetemplates.com/steel/80crv2

[Learn](https://knifetemplates.com/guides) / [Steel](https://knifetemplates.com/steel)

80CrV2 is a popular choice for working knives. The detail I would pay most attention to is how the bar was supplied, because its starting structure changes how it hardens.

[Knife Templates](https://knifetemplates.com/makers/knife-templates) · 2 min read

## What it is

80CrV2 has 0.80% carbon, just like 1080, with 0.5Cr and 0.4Mn where 1080 has 0.75Mn. The V in the name is vanadium. It is not stainless.

*80CrV2 and 1080 compared*

|  | Carbon | Other |
| --- | --- | --- |
| 80CrV2 | 0.80% | 0.5Cr-0.4Mn, with vanadium |
| 1080 | 0.80% | 0.75Mn |

## What the testing found

Toughness: "80CrV2 has quite good toughness; I have found slightly better toughness than 1084, in fact." Hardenability: "So 80CrV2 has reasonably good hardenability," and "With a fine carbide structure it will fully harden even with 1/4″ stock quenched in slow oil."

Edge retention is the other side: "its wear resistance as measured by a CATRA edge retention test is very low on the chart." That is the trade it offers: good toughness and hardenability, and not much edge life.

It has a practical place: it is relatively inexpensive and used by many forging bladesmiths. Forge testing puts it with 1084 as best for general purpose knives.

## Where to be careful

The tempering limit is explicit: do not temper 80CrV2 above 450°F, and the 300°F temper looks attractive for thin knives with high cutting performance. Austenitising was 1525°F for 10 minutes, longer for stock thicker than 1/8″.

Datasheets disagree about 80CrV2 more than most: virtually every one recommends something different. The route on this site is the one from the independent tests.

## Where this comes from

- [How to Heat Treat 80CrV2](https://knifesteelnerds.com/2022/06/23/how-to-heat-treat-80crv2/), Knife Steel Nerds. Larrin Thomas’s tests of 80CrV2, with datasheet comparisons. Test coupons were sealed in stainless foil.
- [How to Heat Treat Knife Steel in a Forge](https://knifesteelnerds.com/2021/09/23/how-to-heat-treat-knife-steel-in-a-forge/), Knife Steel Nerds. A method for reducing forge error, tested on seven low alloy steels. The author still recommends a furnace or a professional for most people.
- [Introduction to Knife Steel Heat Treating from a Metallurgist](https://knifesteelnerds.com/2024/09/17/introduction-to-knife-steel-heat-treating-from-a-metallurgist/), Knife Steel Nerds. The stages, equipment, datasheets and what to do when datasheets disagree. Larrin Thomas’s own recommendations; it gives no schedule for a particular steel.
- [How to Heat Treat 80CrV2](https://knifesteelnerds.com/2022/06/23/how-to-heat-treat-80crv2/), Knife Steel Nerds. Original experiments by metallurgist Larrin Thomas. Starting microstructure, hold and quench stay together. Do not transfer experimental property values to a different process.

[Next up Knife steel: 5160 A low alloy spring steel known for toughness, with a narrow tempering window.](https://knifetemplates.com/steel/5160)

## Keep reading

- [5160 or 80CrV2?](https://knifetemplates.com/steel/5160-vs-80crv2)
- [Knife steel: 1084](https://knifetemplates.com/steel/1084)
- [Knife steel: 52100](https://knifetemplates.com/steel/52100)
- [Choosing steel for a knife](https://knifetemplates.com/steel)
- [All steel pages](https://knifetemplates.com/steel)

## Put it into practice

[Choose a template](https://knifetemplates.com/templates) [Read the print guide](https://knifetemplates.com/guides/print-at-actual-size) [Arrange blanks on stock](https://knifetemplates.com/nest)
