# Knife steel: CPM-154

> What CPM-154 is, its typical composition, how its toughness rates against other stainless steels, and why a different datasheet is preferred.

Source: https://knifetemplates.com/steel/cpm-154

[Learn](https://knifetemplates.com/guides) / [Steel](https://knifetemplates.com/steel)

CPM-154 is easy to finish and well rounded. It is also the steel in this section where the testing admits plainly that one early result looked too good.

[Knife Templates](https://knifetemplates.com/makers/knife-templates) · 2 min read

## What it is

CPM-154 is known for its ease in finishing, combined with good all-around properties including good potential hardness, edge retention and toughness. Crucible's sheet lists "cutlery, bearings, and corrosion resistant tooling" as typical applications. The source article reports no corrosion test of its own, so I make no claim beyond its 14% chromium.

*CPM 154 typical composition (producer data sheet, as published by a distributor)*

| Element | Content |
| --- | --- |
| Carbon | 1.05% |
| Chromium | 14.00% |
| Molybdenum | 4.00% |

## What the testing found

On toughness, CPM-154 compares favourably to other PM stainless steels, similar to S35VN and better than steels like Elmax, Super Gold 2 and S45VN. It also showed superior toughness to conventional steels Niolox, D2 and CruWear, better toughness than the much higher carbon M390, and lower toughness than AEB-L.

On hardness, 2025°F "was still found to be the peak in hardness," and a 300°F temper "still resulted in over 64 Rc, which is high enough for most any knife."

## The result nobody could explain

An earlier set of specimens measured much higher toughness than expected. On review that measurement just looked too high: every other steel with a similar carbide content maxed out around 10 ft-lbs, and there was no clear reason why CPM-154 would manage such high toughness. The cause was never worked out. So read the favourable comparison above as the best retested results, not as a promise.

## Where to be careful

The advice is to use the Latrobe datasheet rather than Crucible's for heat treating 154CM and CPM-154. The route also depends on a cold step, because these heat treatments should not be assumed to work without cryo. The sheet also warns that tempering at 800 to 1100°F "will result in sensitization."

## Where this comes from

- [How to Heat Treat CPM-154: Toughness Experiments](https://knifesteelnerds.com/2020/03/16/how-to-heat-treat-cpm-154-toughness-experiments/), Knife Steel Nerds. Larrin Thomas’s hardness and toughness tests of CPM-154, with datasheet comparisons. It includes an earlier toughness result he could not explain. The charts are images, so this site quotes only the text.
- [CPM 154 data sheet](https://nsm-ny.com/content/uploads/2021/07/CPM154ds.pdf), Niagara Specialty Metals. The CPM 154 data sheet as published by a distributor of Crucible’s CPM steels; Crucible’s own copy was not reachable, and the copy is undated. Producer data, a different route from Larrin Thomas’s, and he advises preferring another datasheet.
- [Knife Steels Rated by a Metallurgist: Toughness, Edge Retention, and Corrosion Resistance](https://knifesteelnerds.com/2021/10/19/knife-steels-rated-by-a-metallurgist-toughness-edge-retention-and-corrosion-resistance/), Knife Steel Nerds. One metallurgist’s ratings, which he says he may change. The rating tables are images, so this site quotes only the text.

## Keep reading

- [Knife steel: S35VN](https://knifetemplates.com/steel/s35vn)
- [Knife steel: CPM MagnaCut](https://knifetemplates.com/steel/cpm-magnacut)
- [Knife steel: D2](https://knifetemplates.com/steel/d2)
- [Choosing steel for a knife](https://knifetemplates.com/steel)
- [All steel pages](https://knifetemplates.com/steel)

## Put it into practice

[Choose a template](https://knifetemplates.com/templates) [Read the print guide](https://knifetemplates.com/guides/print-at-actual-size) [Arrange blanks on stock](https://knifetemplates.com/nest)
