# Knife steel: CPM MagnaCut

> What CPM MagnaCut is, Crucible's published composition, toughness and edge retention figures, and how its corrosion resistance has been tested.

Source: https://knifetemplates.com/steel/cpm-magnacut

[Learn](https://knifetemplates.com/guides) / [Steel](https://knifetemplates.com/steel)

MagnaCut gets plenty of attention, but I would approach it as a furnace process to establish carefully. An expensive bar is a good reason to prove the setup on an offcut first.

[Knife Templates](https://knifetemplates.com/makers/knife-templates) · 3 min read

## What it is

Crucible describes it as "a unique powder metallurgy stainless tool steel with a design which eliminates chromium carbide in the heat treated microstructure," which it says gives properties "similar to non-stainless steel CPM 4V." Its designer is also the metallurgist whose testing this page draws on, so keep in mind that the steel's designer is also the person testing it.

*CPM MagnaCut composition (Crucible data sheet)*

| Element | Content |
| --- | --- |
| Carbon | 1.15% |
| Chromium | 10.7% |
| Vanadium | 4.00% |
| Molybdenum | 2.00% |
| Niobium | 2.00% |
| Nitrogen | 0.20% |

## The producer's figures

These are Crucible's own, so they are not independent testing. By their SEM analysis, MagnaCut carries 8.0% total carbide (6.5% vanadium carbide, 1.5% niobium carbide, no chromium carbide), against 13.0% for S35VN, 16% for CPM 154 and 22% for S90V. Crucible measured MagnaCut's from micrographs, and its S35VN figure is an estimate from software.

On toughness, the sheet says MagnaCut "is very resistant to chipping and breaking." On edge retention, it reports CATRA results relative to 440C at 100, with MagnaCut at 135. Hardness differs between the rows of both tables, so compare them with that in mind.

*Crucible's Charpy toughness figures (ft-lbs)*

| Steel | Hardness (HRC) | Toughness |
| --- | --- | --- |
| MagnaCut | 62.5 | 38 |
| MagnaCut | 64 | 30 |
| 4V | 62 | 36 |
| CPM 154 | 60 | 26 |
| S35VN | 61 | 25 |
| S45VN | 61.5 | 19 |
| S90V | 61 | 17 |
| 20CV | 62 | 15 |

*Crucible's CATRA edge retention, relative to 440C at 100*

| Steel | Hardness (HRC) | Relative |
| --- | --- | --- |
| S90V | 61.5 | 195 |
| 20CV | 61.5 | 155 |
| S45VN | 61.5 | 140 |
| MagnaCut | 62.5 | 135 |
| S35VN | 61 | 130 |
| CPM 154 | 61 | 120 |
| 440C | 56 | 100 |

## What the testing says

It rates as the most balanced of the steels charted, in an area all by itself on the chart. On corrosion, a 1% saltwater test showed no visible corrosion after 72 hours, though the steel is on the border of being a saltwater steel and is not really for diving knives. It suits everything from thin slicers and kitchen knives to large chopping knives.

## What it asks of the maker

The tested route is 2050°F austenitize, plate or oil quench, and a 2×2 hour 350°F temper. Crucible's sheet gives 1950 to 2200°F for the hardening heat, with the hold set by temperature (20 minutes at 2050°F), a double temper at 300 to 450°F, and the warning that tempering above 750°F reduces corrosion resistance. A freezer has no effect unless it is used directly after the quench with no delay. The route page is Crucible's.

## Where this comes from

- [CPM MagnaCut data sheet, issue 1, March 2021](https://www.alphaknifesupply.com/Pictures/Info/Steel/CPMMagnaCut-DS.pdf), Crucible Industries. The producer’s own composition, toughness, edge retention, annealing and heat treatment figures. Producer data, not independent testing.
- [CPM MagnaCut: The Next Breakthrough in Knife Steel](https://knifesteelnerds.com/2021/03/25/cpm-magnacut/), Knife Steel Nerds. Larrin Thomas’s account of MagnaCut. He developed the steel, which the article acknowledges.
- [Knife Steels Rated by a Metallurgist: Toughness, Edge Retention, and Corrosion Resistance](https://knifesteelnerds.com/2021/10/19/knife-steels-rated-by-a-metallurgist-toughness-edge-retention-and-corrosion-resistance/), Knife Steel Nerds. One metallurgist’s ratings, which he says he may change. The rating tables are images, so this site quotes only the text.

[Next up Knife steel: 8670 A tough nickel-chromium low alloy steel with an easy heat treatment and low wear resistance.](https://knifetemplates.com/steel/8670)

## Keep reading

- [AEB-L or MagnaCut?](https://knifetemplates.com/steel/aeb-l-vs-magnacut)
- [Knife steel: AEB-L](https://knifetemplates.com/steel/aeb-l)
- [Carbon, stainless, tool and powder metallurgy steels](https://knifetemplates.com/steel/carbon-stainless-tool-and-powder)
- [Foil or coatings: protecting knife steel](https://knifetemplates.com/heat-treating/protecting-the-steel)
- [Choosing steel for a knife](https://knifetemplates.com/steel)
- [All steel pages](https://knifetemplates.com/steel)

## Put it into practice

[Choose a template](https://knifetemplates.com/templates) [Read the print guide](https://knifetemplates.com/guides/print-at-actual-size) [Arrange blanks on stock](https://knifetemplates.com/nest)
