# Knife steel: D2

> What D2 is, its composition from Carpenter, why it is not stainless, how it compares with PSF27, CPM-D2 and CPM-154, and what it asks of the shop.

Source: https://knifetemplates.com/steel/d2

[Learn](https://knifetemplates.com/guides) / [Steel](https://knifetemplates.com/steel)

D2 has been in knives for decades and is still common. It is a tool steel with plenty of chromium, and that chromium is the thing most people get wrong about it.

[Knife Templates](https://knifetemplates.com/makers/knife-templates) · 2 min read

## What it is

Carpenter describes its D2 as "an air hardening, high-carbon, high-chromium tool steel." It has been a mainstay in knives for decades, and in recent years it has been popular in budget production folders.

It is not stainless. With about 12% chromium, the high carbon content means many chromium carbides form, so the chromium is tied up. Carpenter says only that the chromium gives "mild corrosion resisting properties in the hardened condition."

*D2 nominal composition (Carpenter data sheet)*

| Element | Content |
| --- | --- |
| Carbon | 1.50% |
| Chromium | 12.00% |
| Vanadium | 0.90% |
| Molybdenum | 0.80% |
| Manganese | 0.50% |
| Silicon | 0.30% |

## What the testing found

The source article covers conventional D2 and two finer-grained versions of the same composition. The finer carbide structure of PSF27 gives superior toughness against conventional D2, and the yet finer structure of CPM-D2 gives better toughness than either. In one comparison, PSF27 at 64 Rc had higher toughness than conventional D2 at 60 Rc.

Against the stainless alternatives: "Ditto for conventional D2 and 154CM, they have similar toughness and edge retention but 154CM is stainless." On edge retention and cold treatment, "a comparison I made between a 36 hour cryo and no cryo D2 at similar hardness led to no difference in edge retention."

Finishing is easier than the carbide content suggests: "Both have primarily chromium carbides making finishing and sharpening relatively easy with aluminum oxide abrasives and stones."

## Where to be careful

Keep the hardening heat in check: restrict austenitizing temperatures to no higher than 1900°F in most cases unless maximum hardness is necessary. The producer's sheet describes a different route from the tested one, so do not mix them: that comparison is on the route page.

## Where this comes from

- [How to Heat Treat D2, PSF27, and CPM-D2](https://knifesteelnerds.com/2020/08/31/how-to-heat-treat-d2-psf27-and-cpm-d2/), Knife Steel Nerds. Larrin Thomas’s tests, mostly on PSF27, with one recommended route for all three because they share a composition. The article states no composition; the figures on this site come from Carpenter’s data sheet.
- [CarTech No. 610 (D2) data sheet](https://www.carpentertechnology.com/hubfs/7407324/Material%20Saftey%20Data%20Sheets/D2.pdf), Carpenter Technology. The producer’s own nominal composition, annealing and hardening figures for D2. Producer data, and a different route from Larrin Thomas’s: it hardens at 1800 to 1875°F and quenches in air.
- [What is the Future of Stainless Knife Steel Design?](https://knifesteelnerds.com/2020/10/12/what-is-the-future-of-stainless-knife-steel-design/), Knife Steel Nerds. Why chromium makes steel stainless and why chromium carbides get in the way.

[Next up Knife steel: Nitro-V A nitrogen-alloyed relative of AEB-L with very good toughness and some untested claims.](https://knifetemplates.com/steel/nitro-v)

## Keep reading

- [Knife steel: CPM MagnaCut](https://knifetemplates.com/steel/cpm-magnacut)
- [What is in knife steel](https://knifetemplates.com/steel/what-is-in-knife-steel)
- [Carbon, stainless, tool and powder metallurgy steels](https://knifetemplates.com/steel/carbon-stainless-tool-and-powder)
- [Choosing steel for a knife](https://knifetemplates.com/steel)
- [All steel pages](https://knifetemplates.com/steel)

## Put it into practice

[Choose a template](https://knifetemplates.com/templates) [Read the print guide](https://knifetemplates.com/guides/print-at-actual-size) [Arrange blanks on stock](https://knifetemplates.com/nest)
