# Knife steel: Nitro-V

> What Nitro-V is, how tests compare it with AEB-L, what nitrogen does and does not do for corrosion resistance, and what is still untested.

Source: https://knifetemplates.com/steel/nitro-v

[Learn](https://knifetemplates.com/guides) / [Steel](https://knifetemplates.com/steel)

Nitro-V is AEB-L with a little nitrogen and vanadium added. It is a good example of a steel where the honest summary is mostly "similar, and not yet fully tested."

[Knife Templates](https://knifetemplates.com/makers/knife-templates) · 3 min read

## What it is

Nitro-V is a stainless steel sold by New Jersey Steel Baron, first released in 2017 and designed as a version of Uddeholm AEB-L modified with nitrogen and vanadium. It looks very similar to AEB-L, with the same C, Cr and Si and a minor difference in Mn, and its nitrogen content is the same as 14C28N. The composition table in the source article is an image, and I found no producer datasheet, so I give no figures.

## What the testing found

"Nitro-V has very good toughness compared with other steels. It has slightly lower toughness than AEB-L for unknown reasons. It is significantly tougher than the powder metallurgy stainless steels like M390, Elmax, and S35VN. Therefore Nitro-V would be well suited to knives requiring good toughness." It reaches about 64 Rc at peak hardness, similar to AEB-L, with a slightly lower best austenitising temperature.

## Edge retention and corrosion

Both are expectations, not results. On edge retention: "Nitro-V is expected to have very similar wear resistance and edge retention to AEB-L, but there has not been any testing to confirm that," and AEB-L "has edge retention similar to 52100, which is significantly lower than higher carbide content stainless steels like 440C, CPM-154, S30V, etc."

On corrosion, the nitrogen did not do what you might hope for chromium: it did not increase chromium in solution for enhanced corrosion resistance. The nitrogen may itself increase corrosion resistance somewhat relative to AEB-L, and 14C28N has significantly more chromium in solution, which likely gives it better corrosion resistance than Nitro-V and AEB-L. The source article ends by saying more corrosion and edge retention testing is needed.

## Where to be careful

The tempering limit is firm: do not go past 350°F on the evidence, because the 450°F temper reduced both hardness and toughness unexpectedly. And the source article does not say which AEB-L it compares with; steel sold as AEB-L can be Buderus X65Cr13, which behaves a little differently.

## Where this comes from

- [Nitro-V: Its Properties and How to Heat Treat It](https://knifesteelnerds.com/2019/09/23/nitro-v-its-properties-and-how-to-heat-treat-it/), Knife Steel Nerds. Larrin Thomas’s tests of Nitro-V against AEB-L and 14C28N, with his heat treatment recommendation. The composition table is an image, so none is given here, and I found no producer datasheet. He says edge retention and corrosion resistance still need testing.
- [Dry Ice vs Liquid Nitrogen vs Freezer: How Cold Do You Need for Cryo?](https://knifesteelnerds.com/2022/01/11/how-cold-for-cryo/), Knife Steel Nerds. Freezer, dry ice and liquid nitrogen compared, on a few steels. The author notes the steel sold to him as AEB-L was not Uddeholm AEB-L.
- [Knife Steels Rated by a Metallurgist: Toughness, Edge Retention, and Corrosion Resistance](https://knifesteelnerds.com/2021/10/19/knife-steels-rated-by-a-metallurgist-toughness-edge-retention-and-corrosion-resistance/), Knife Steel Nerds. One metallurgist’s ratings, which he says he may change. The rating tables are images, so this site quotes only the text.

[Next up Knife steel: S35VN A balanced powder metallurgy stainless steel, tougher and easier to grind than S30V.](https://knifetemplates.com/steel/s35vn)

## Keep reading

- [Knife steel: AEB-L](https://knifetemplates.com/steel/aeb-l)
- [Knife steel: CPM MagnaCut](https://knifetemplates.com/steel/cpm-magnacut)
- [Cold treatment and cryo for knives](https://knifetemplates.com/heat-treating/cold-treatment)
- [Choosing steel for a knife](https://knifetemplates.com/steel)
- [All steel pages](https://knifetemplates.com/steel)

## Put it into practice

[Choose a template](https://knifetemplates.com/templates) [Read the print guide](https://knifetemplates.com/guides/print-at-actual-size) [Arrange blanks on stock](https://knifetemplates.com/nest)
