What stock removal means
Stock removal is how most of us make a first knife. You start with a flat bar of steel and take away everything that isn't the knife: cut the outline, drill the holes, grind the bevels, harden and temper the blade, fit a handle, then sharpen it. Forging moves the steel into shape with heat and a hammer instead. Even most amateur forgers grind the blade to its final shape, so the grinding in this guide is useful either way.
Steel when doing stock removal still has to be hardened and tempered, either by you or by someone you pay to do it. Heat treatment and geometry specifically reward an engineering mindset more than an artistic one. That is why this guide spends more time on order and checking than on technique.
Before you start: safety
Grinding makes noise, sparks and fine dust, and a belt takes skin as readily as steel. The basics I'd treat as the minimum:
- Safety glasses.
- Hearing protection for loud jobs like grinding.
- A dust mask or respirator, and a separate grinding space or the great outdoors when you can manage it.
- Long sleeves and enclosed shoes, and a change of clothes before you go back into clean areas, because grinding dust travels.
- Nitrile gloves for epoxy and solvents.
The simplest rule of all: keep your hands away from the belt. Work slowly, and stop if you are tired.
Two things need their own planning. If you quench in oil, have a fitted metal lid for the tank and suitable fire protection within reach before the steel comes out of the furnace. And treat handle-material dust (G10, Micarta and similar) seriously. Makers on the forums disagree about some of the details of what is in that dust, which to me is a reason to read the supplier's safety data sheet and wear a proper respirator, not a reason to skip one.
What you actually need
You need less than the internet suggests to get started. Hand files, clamps, and a hacksaw or an angle grinder are the minimum for shaping a blade, with a proper knife grinder a later upgrade. You will also want a drill, sandpaper, a marker and a scribe, a ruler, and somewhere safe to work.
The expensive, specialised part is heat treatment, which needs controlled temperatures and a proper quench. Plan for that early, not after you have spent a weekend on the grinder.
The order of work
1. Choose a knife and print the template at actual size
Pick a template, or open one in the editor and change what you want. Print at 100% or Actual size, never Fit to page, and measure the 100 mm ruler on the sheet before you trust any other dimension. The print guide covers joining the sheets. Tape them together where they join and cut the paper out.
Then hold the paper handle in your hand. It costs nothing to find out now that a handle is too short or too chunky. If you are choosing between shapes, compare up to three profiles at the same scale first.
2. Choose the steel
I would start with a plain carbon steel that comes with a name, a supplied condition and a published heat treatment schedule. Knife Steel Nerds has published heat treatment experiments on many popular grades, and steel suppliers publish their own data sheets. Steel of unknown origin (a file, a spring, a saw blade) stays an experiment. A spark test narrows the possibilities, but it can't guarantee which steel you have.
Bar thickness is something the template can't decide for you. It comes from the knife you want. A thin kitchen blade and a thick field knife start from different bars, and thicker stock means more grinding. If you are cutting several blanks, Arrange on stock shows how they fit on a bar and what is left over.
3. Mark the outline on the steel
Stick the paper template to the bar, or trace around it. Either way, mark the outline into coloured steel (layout dye or a marker) with a scribe, so the line survives the grinder. Centre punch the hole positions. Colouring the edge with a marker and scribing a centre line along it carries the same idea on to the bevel.
4. Cut and shape the profile
Cut outside the line with a hacksaw, angle grinder or bandsaw, then bring the steel to the line with files or a belt. Take your time on the curves. A smooth outline now saves a lot of fairing later.
Keep the edge side thick and flat for now. Most of us finish the bevels after heat treatment, and the thickness you leave at the edge is a decision worth writing down. I record it at the heel, the middle and the tip. If your steel supplier or heat treater gives a limit for edge thickness before hardening, follow that.
5. Drill the holes while the steel is soft
Drill pin holes, lanyard holes and anything else now. Hardened steel is hard on drill bits, and you would need carbide tooling to drill it at all. Decide on your pin size before you drill, and check that the holes match the hardware you have in the drawer. Deburr every hole so it doesn't scratch a scale or hold up a pin.
6. Rough in the bevels
Even bevels are the part most of us find hardest. Grind from the plunge area toward the tip, check after every pass, and stop short of the final line. Tharwa Valley Forge teaches a push stick method that starts with a used 50 grit belt and saves new belts for after heat treatment. The steel is cooled in water after a few passes, and after every pass once the blade is hardened.
That last point matters. A thin edge can overheat while the rest of the blade feels cool. Cool the steel often and stop grinding the edge long before it feels hot.
7. Heat treat
I won't put a schedule in a general guide, because the right one belongs to your steel. Knife Steel Nerds publishes experiments for many grades, and suppliers publish data sheets. Keep the hardening temperature, hold time, quench and temper together from one source, because numbers from different sources are not interchangeable.
A few habits help whatever steel you use:
- Make a small test piece from the same bar and put it through the same run, so you can test it rather than the knife.
- Temper soon after the quench, as your schedule says.
- Look the bare blade over for cracks and warp before any handle work. A cracked blade is retired, not repaired.
If you would rather not do this yourself, sending the blades out to be hardened is a completely respectable choice.
8. Finish grind and hand sand
Now the bevels come to their final shape, with fresh belts. After that, hand sanding takes care of the scratches. Bjorn Jacobsen at Nordic Edge puts 80 to 90% of the work in the first grit, getting the blade truly flat and even. Change direction with each grit, so you can see when the previous scratches are gone. Stop at 180 grit before making the guard and handle, because those steps tend to scratch the blade.
Finish the blade to a sensible grit, then make the handle, then do the final finish.
9. Make the handle
A full tang takes two scales pinned or glued on either side. A hidden tang goes into a slot in the handle. Dry fit everything before any epoxy comes out, and check that the handle sits where your hand wants it. If you are choosing between these two, there is more on how each is built in my guide to full tang and hidden tang knives.
10. Sharpen and test
Decide which angle you mean before you start. Fifteen degrees per side is 30 degrees included, and it is worth writing down which you are using. Raise a burr, remove it, and test the edge on something soft before you trust it on something hard. If a carefully made edge fails quickly in normal use, look at the geometry and the heat treatment record before blaming the steel.
Mistakes I would avoid
- Using unidentified steel and expecting a textbook result.
- Thin edges before heat treatment.
- Drilling after hardening.
- Chasing a polish before the bevels are even.
- Skipping the test piece, then not knowing what went wrong.
- Treating protection as optional because the job is short.
Where this comes from
I leaned on Nordic Edge's guide to getting into knifemaking, their safety page and their hand sanding guide, Tharwa Valley Forge's push stick grinding tutorial and their recycled steel identification page, and Larrin Thomas's work at Knife Steel Nerds. If you do anything different at the bench, leave a comment below. I would like to hear it.
Comments
Questions, corrections and what worked for you. Upvote comments you find useful.
Loading comments…