Learn / Maker guide

Full Tang vs Hidden Tang: What They Are and How to Choose

What full, partial, hidden and push tangs are, and how each is built, with notes on the templates here.

By Knife Templates · Updated 11 Nov 2026 · 7 min read

What a tang is

The tang is the part of the blade steel that goes into the handle. Everything else about the handle (the scales, the pins, the epoxy, the ferrule) is how that steel is held. The two constructions people argue about most are the full tang and the hidden tang.

Terms here overlap, so I'll start by defining them.

  • Full tang. A full tang extends the full length of the grip portion of the handle, and may be narrower or wider than the handle. Some makers and retailers also expect the tang to match the handle's width, so the steel shows around the edges with a scale on each side. If you are buying, ask which one the seller means.
  • Partial tang. Stub, half and three-quarter tangs are named for how far the tang extends into the handle.
  • Hidden tang. The tang is fastened inside the handle so that neither the tang nor the way it is fastened can be seen. The simplest method is epoxy. Others are a protrusion that fits a notch in the handle, and threading the tang so a nut at the butt holds everything together.
  • Stick or rat-tail tang. A tang that is narrower than the rest of the blade. There is an abrupt reduction in metal where the blade meets the tang, and this style is often seen on decorative blades that aren't meant for real use. A hidden tang may or may not be a stick tang.
  • Push tang. A tang that is pushed into a pre-made handle and fastened there.
  • Encapsulated tang. The handle material is moulded around the tang.

Is full tang stronger?

This is the question people actually ask. The honest answer is that a full tang is the more forgiving design, and a well-made hidden tang can be perfectly strong. I could not find a published controlled comparison of the two. Retailer pages often call full tang one of the strongest constructions without any test behind it, and most of what I found from makers is experience, not data. Here is what the makers say.

Where the weak point is matters most. The junction between the blade and the handle is one of the weakest areas of a knife. On the KnifeDogs forum, a maker posting as DLBrothers places the main risk in a hidden tang at the guard and handle junction, where the steel changes shape and stress concentrates. His summary is short: "Weak attachment=weak point." He adds that a tighter junction makes the whole knife stronger.

Other makers stress workmanship over layout. John Andrews, in the same thread, has made hidden tang knives for more than 20 years, and says properly hidden pins and good epoxy make "a strong enough handle for a user knife", with no complaints from clients who use their knives. Nothing in that is a test result, but it is a long record from someone who uses hidden tangs, and I'd weigh it that way.

The makers also disagree about how much steel a tang needs. One poster argued that removing metal from a tang to lighten it loses strength. DLBrothers argued the other way, using an I-beam as the analogy: the load runs along the outer edges, so the middle can be thinned if a rim and a few bridges remain, and the scales, epoxy and pins all contribute. That is a fair summary of an argument that hasn't been settled.

What I take from this is simple. A sharp inside corner is a classic place for stress to concentrate, so rounding the corner where the blade steps down into the tang is sensible; in the editor, the machi junction radius rounds the underside of that step. Beyond that, how well the handle is fitted and fastened seems to count for more than the label on the construction.

What each costs you

Strength is only one of the differences, and not always the deciding one.

  • Weight and balance. A full tang carries more steel into the handle, so the knife is heavier. A retailer comparison I read credits hidden tangs with lighter weight and better balance for slicing, but it gave no measurements. I'd treat that as likely rather than proven, and check balance on the knife in your hand.
  • Handle material. John Andrews points out that a full tang wastes premium handle material such as stabilised burl or horn, because the centre of the block ends up as sawdust. That matters if you are working with an expensive piece.
  • Repair. The retailer comparison I mentioned lists a full tang as easier to inspect and repair, and a hidden tang as harder to repair if something inside lets go.
  • Difficulty. Fred Rowe, quoted in the KnifeDogs thread, saw hidden tangs as the bigger craftsmanship challenge, with more design options. DLBrothers made the fair point that difficulty alone doesn't make a design better.
  • Looks. DLBrothers also notes that part of the choice is about what buyers think looks better and sells better. That is a legitimate reason as long as you are honest about it.

How each is built

A full tang handle is made by shaping the handle material around the tang. The scales are fastened with pins, screws, bolts, metal tubing, epoxy and similar. You drill the pin holes in the steel while it is soft, which is why a full tang template carries holes.

A hidden tang handle is made by fitting a slot or hole to the tang precisely, then fastening it with epoxy, a notch or a threaded nut. Because the tang can't be seen once it is done, the fit matters a great deal. Dry fit it before epoxy comes anywhere near it. Japanese wa handles are hidden tang handles too, and the tang there is the nakago, the part of the metal to which the handle is attached.

How to choose

I'd ask four questions.

  1. What will the knife do? A knife that gets pried, twisted or used hard puts more load on the handle joint. Full tang is the preferred style for hard-use fixed blades, so I'd lean that way, or toward a hidden tang I was very confident in.
  2. What handle material do I want to use? Valuable or delicate material argues for a hidden tang. Tough, flat scale stock is happy on a full tang.
  3. How comfortable am I with precise fitting? A hidden tang needs a slot fitted precisely to the tang. Full tang scales need flat mating surfaces and pin holes that line up.
  4. How heavy do I want it? Hold a printed template and ask whether a heavier handle suits the way you cut.

Which templates here use which

The kitchen templates are hidden tang designs. The full tang utility and outdoor templates draw the handle itself, with a handle outline and holes for your pins. You can browse the kitchen templates and the outdoor templates, or open either in the editor. The editor's tang style presets set the length, whether the tang tapers to the butt or runs straight, and whether the square shoulders are cut. For a full tang, a handle style is a handle shape traced from a real knife, kept in millimetres, so it stays hand-sized whatever the blade is.

Whichever you pick, print at actual size and hold the paper outline first. The print guide shows how, and the editing guide covers changing the tang and handle.

Where this comes from

Wikipedia's article on tangs, Blade Magazine's anatomy of a knife, the maker discussion in the KnifeDogs thread Why so many hidden tangs (DLBrothers, John Andrews and Fred Rowe), and Knifemaking.com's full tang and hidden tang comparison. If you have broken one or the other, tell us how in a comment. That evidence is hard to come by.

Comments

Questions, corrections and what worked for you. Upvote comments you find useful.

Loading comments…

Knife Templates