What it is
Crucible describes it as "a unique powder metallurgy stainless tool steel with a design which eliminates chromium carbide in the heat treated microstructure," which it says gives properties "similar to non-stainless steel CPM 4V." Its designer is also the metallurgist whose testing this page draws on, so keep in mind that the steel's designer is also the person testing it.
| Element | Content |
|---|---|
| Carbon | 1.15% |
| Chromium | 10.7% |
| Vanadium | 4.00% |
| Molybdenum | 2.00% |
| Niobium | 2.00% |
| Nitrogen | 0.20% |
The producer's figures
These are Crucible's own, so they are not independent testing. By their SEM analysis, MagnaCut carries 8.0% total carbide (6.5% vanadium carbide, 1.5% niobium carbide, no chromium carbide), against 13.0% for S35VN, 16% for CPM 154 and 22% for S90V. Crucible measured MagnaCut's from micrographs, and its S35VN figure is an estimate from software.
On toughness, the sheet says MagnaCut "is very resistant to chipping and breaking." On edge retention, it reports CATRA results relative to 440C at 100, with MagnaCut at 135. Hardness differs between the rows of both tables, so compare them with that in mind.
| Steel | Hardness (HRC) | Toughness |
|---|---|---|
| MagnaCut | 62.5 | 38 |
| MagnaCut | 64 | 30 |
| 4V | 62 | 36 |
| CPM 154 | 60 | 26 |
| S35VN | 61 | 25 |
| S45VN | 61.5 | 19 |
| S90V | 61 | 17 |
| 20CV | 62 | 15 |
| Steel | Hardness (HRC) | Relative |
|---|---|---|
| S90V | 61.5 | 195 |
| 20CV | 61.5 | 155 |
| S45VN | 61.5 | 140 |
| MagnaCut | 62.5 | 135 |
| S35VN | 61 | 130 |
| CPM 154 | 61 | 120 |
| 440C | 56 | 100 |
What the testing says
It rates as the most balanced of the steels charted, in an area all by itself on the chart. On corrosion, a 1% saltwater test showed no visible corrosion after 72 hours, though the steel is on the border of being a saltwater steel and is not really for diving knives. It suits everything from thin slicers and kitchen knives to large chopping knives.
What it asks of the maker
The tested route is 2050°F austenitize, plate or oil quench, and a 2×2 hour 350°F temper. Crucible's sheet gives 1950 to 2200°F for the hardening heat, with the hold set by temperature (20 minutes at 2050°F), a double temper at 300 to 450°F, and the warning that tempering above 750°F reduces corrosion resistance. A freezer has no effect unless it is used directly after the quench with no delay. The route page is Crucible's.
Where this comes from
- CPM MagnaCut data sheet, issue 1, March 2021, Crucible Industries. The producer’s own composition, toughness, edge retention, annealing and heat treatment figures. Producer data, not independent testing.
- CPM MagnaCut: The Next Breakthrough in Knife Steel, Knife Steel Nerds. Larrin Thomas’s account of MagnaCut. He developed the steel, which the article acknowledges.
- Knife Steels Rated by a Metallurgist: Toughness, Edge Retention, and Corrosion Resistance, Knife Steel Nerds. One metallurgist’s ratings, which he says he may change. The rating tables are images, so this site quotes only the text.
Comments
Questions, corrections and what worked for you. Upvote comments you find useful.
Loading comments…