Learn / Heat treating

Heat treating AEB-L

AEB-L is worth a look for a stainless kitchen knife, especially when you want a fine edge. The workshop requirement steps up from simple carbon steel: controlled high heat, protection from the atmosphere and a planned cold treatment.

Knife Templates · 5 min read

Where I would start

A fine-carbide stainless steel used in cutting applications. Stainless still needs cleaning and drying; a completed heat treatment and suitable finish are part of getting the corrosion performance you expect.

Annealed AEB-L, controlled furnace and the NJSB plate-quench plus cold-treatment route. A lower-temperature route without cold treatment is a different process and has different retained-austenite behaviour.

Get the equipment ready

A furnace capable of stable stainless hardening temperatures, correctly rated stainless foil or another suitable protective system, aluminium quench plates, compressed air and a properly managed sub-zero setup.

Measure the furnace and tempering oven independently where possible. A controller display is a setpoint, not proof that the whole blade has reached it. Timing a hold starts after equalisation, not as soon as the door closes.

A process to work from

Use this as a complete route to establish on a coupon from your stock. Temperatures in Celsius are rounded conversions of the Fahrenheit setpoints. A different supplier, section or starting condition can need a different process.

AEB-L: worked heat-treatment route
StageWhat to do
Protect and preheatUse a clean, correctly sealed, temperature-rated foil packet. Preheat at 816°C / 1500°F for 15 minutes.
Austenitise1066°C / 1950°F for 15 minutes after equalisation.
QuenchQuench between aluminium plates with compressed air to 50°C / 125°F or below. Keep plate contact effective across the blade.
Cold treatmentAfter cooling to room temperature, use the specified sub-zero route: approximately −74°C / −100°F for 30–60 minutes. Liquid nitrogen is an alternative in the supplier’s process; it is not the same temperature as a dry-ice bath.
TemperReturn to room temperature, then 177°C / 350°F for 2 hours. Cool to room temperature and repeat for 2 hours. Cold treatment must be followed by tempering.

The detail to pay attention to

A household freezer does not reproduce a −74°C bath. Do not raise the hardening temperature to compensate for missing cold-treatment equipment. Select and validate a complete no-cold route if that is the process you can actually run. The producer’s own sheet, an old undated scan for the strip steel, is a different route: harden at 1050°C (1920°F) and cool to room temperature, or at 1080°C (1975°F) with a subzero treatment to −60°C (−76°F), in oil and not water, with the hold read from a graph and the heating-up time added. It says a temper of at least 150°C (300°F) is needed for a minimum of toughness, and that tempering above about 400°C (750°F) loses the corrosion resistance. Keep the two apart.

Thin kitchen blades make quench contact worth planning. The packet should not have a folded seam between a blade face and a plate. Rehearse handling with a cold packet. Cryogenic liquids need a suitable vessel, ventilation, face and hand protection, and training; never use a sealed container or improvise a flammable solvent bath beside a hot furnace.

Check the result before fitting the handle

Clean scale and decarburisation from the test surface before interpreting a hardness reading. Use a flat, supported area and a calibrated method appropriate to the sample thickness. A file skating across a blade is a rough check, not an HRC measurement.

Inspect the tempered blade in good light for cracks, edge waves and distortion. If a blade is cracked, retire it. If hardness is unexpectedly low, check the whole record before increasing temperature or repeating a quench.

Keep a record

Keep the stock supplier and batch, blade and edge thickness, furnace program, actual hold, oil or plate details, cold-treatment branch and temper cycles beside the editable design. Add measured hardness and where it was measured.

After grinding and sharpening, evaluate the finished knife in its intended cutting work. Keep notes on edge stability, sharpening and geometry. Change one main variable so you can tell what helped as you learn.

Where this comes from

  • AEB-L Heat Treat, July 2020, New Jersey Steel Baron. Supplier schedule for controlled equipment. Fahrenheit is authoritative where the PDF prints an inconsistent Celsius conversion. Example setpoints below sit inside its ranges; no hardness is guaranteed.
  • UHB Stainless AEB-L data sheet (undated scan), Uddeholm. The producer’s own sheet for the strip steel, as a scan hosted by Knife Steel Nerds. It is undated, I found no current producer sheet, and it gives hold times only as a graph. Producer data, and a different route from the supplier’s.
Next upHeat treating CPM MagnaCutCPM MagnaCut: the equipment, hardening hold, quench, temper and details that are easy to miss.

Comments

Questions, corrections and what worked for you. Upvote comments you find useful.

Loading comments…

Knife Templates